Stainless Steel 304 Wire Filter Mesh Acid And Alkali Resistant Filter Cap Fine Workmanship

Wire Filter Mesh Product Description

1. Machine: generally, the larger tonnage oil press (200T) is used to stretch the mold of the plate.

2. mold: Angle can not be too straight, generally direct 10 above, the structure should be reasonable.

3. material: generally required plate thickness range of 0.8-1.0mm, beyond this range, even 500T of the

hydraulic press is also powerless.

4. Heat treatment: generally, high temperature annealing treatment is required for the overall tensile water

tank, which is generally above 1200 degrees to eliminate the internal stress after stretching.

5. Surface treatment: drawing, polishing and polishing (generally smooth)

6. Technology: after the drawing oil of the mold is added to the plate, the drawing can be carried out smoothly.

After the molding, the annealing treatment is carried out, and then the surface treatment is carried out.

Manual molding.

Product Parameter

The bottom welding basin is the best under the current (2012) technical conditions, the reason is that: the

overall stretch of the tank generally needs high temperature annealing, generally more than 1200 degrees

of temperature, after such treatment of the tank, the steel naturally becomes weak, the hardness of the tank

must be reduced, this is one;

Second, generally used steel plate thickness is 0.8-1.0mm, then more than this thickness, it can be said that

even 500 tons of hydraulic press is of no use, so from this point, the overall tension of the basin, thickness is

difficult to guarantee;

Third, in the side treatment, the overall stretching of the basin, generally for a single layer of flanging, on the

one hand is likely to cut the hands of the installation workers, the most important is no "" reinforcement ", bearing

weight is not good enough, at the same time, it is difficult to have the effect of sealing water;Fourth, the overall

stretchingof the panel may be difficult to do flat;

Wire Filter Mesh Process Defects

For butt welding basin, the most difficult to do is to ensure the surface of the basin is flat, if you can ensure,

then it is really the best way, because: it is the same as the whole drawing material, but also can solve the

problem of stretching, but many butt welding basin on the market, it is difficult to perfect;

For the bottom welding, I think, is the most mature and the best molding technology.Premise is, must be

numerical controlwelding.Manual welding basin, it is easy to appear welding point is not uniform, in fact, the

continuous repair of the traces of welding.The introduction of the most advanced CNC welding technology,

and CNC welding to avoid the phenomenon of virtual welding, welding leakage.

Wire Filter Mesh Warm Reminder

Remind everybody, when choosing basin, can look at welding place to have very fine one after another

seam seriously, have words, it is certain to be empty weld, so, accumulate over a long period of time, hide

filth, can come loose;Remind everybody again: when buying cistern, can touch with the hand in basin wall

part, see to have no bump, high-grade cistern won't have bump;Again and again, buy a stretch tank, pay

attention to the thickness of the tank and the capacity.

Notice The Choose And Buy

When flume of choose and buy, should consider depth above all, the flume of partial entrance does not

suit domestic large pot to provide, it is size next.Whether the bottom has moisture-proof measures is also

not omitted, and pay attention to the followingpoints.According to the size of the ambry table surface to

determine the size of the sink, because the sink can be installed on thestage, in the stage, under the stage,

so the size of the choice is different.When selecting the stainless steel sink, the material thickness should

be moderate, too thin will affect the sink service life and strength, too thick is easy to damage the washing

tableware.See the flatness of stainless steel surface even additionally, if uneven, explain quality is poor.Normally,

clean the flume with bigger capacity is practical good, the depth is better with 20 centimeters left and right sides,

can prevent splash outside appropriately so.The surface treatment of the water tank with a matt surface as

beautiful and practical, the water tank welding place to carefully observe, the weldmust be flat and uniform,

no rust spots.

Product Picture

About Company

Anping County Jineng metal Wire Mesh Products Co., Ltd. was established in 2008. Our company is located in Anping County of Hebei Province. Anping County is China's wire mesh production base, which in known as "home of wire mesh". We have more than 50 employees, including more than 10 professional technical personnel and senior engineers. We are production-oriented enterprises which is specialized in environmental protection, water treatment, chemical and other filtration equipment and accessories. Meanwhile we are engaged in the intensive processing of wire mesh according to the advantages of Anping as China's wire mesh production base.

Our company has a scientific management system and passed the ISO9001 quality management system certification.Every production step has strict quality test. Our company has a complete set of testing equipment: material component testing, finished product testing, experimental results testing equipment.

Our company has cooperated with many colleges and universities to attract technical talents and management talents. We invested in the research and development of new products, and we got multiple patents.

Our products meet the requirements of foreign cooperative enterprises.Our annual sales of export to European and American countries, such as France, Spain, Germany, America, Canada, Australia, Japan and other countries, are growing at a rate of 35%. We look forward to the cooperation with enterprises from all over the world.